Installation Instructions for Wide Angle Door Viewers

 

Tools required for Installation (UltraVision – SuperVision – WideVision)

 

1-     Power Drill

2-     Hole Saw with pilot drill bit

3-     Small  1/8” drill bit

4-     Tape Measure  &  carpenter’s level

5-     Pencil

 

1-     Use the tape measure to determine the best height to install the Viewer on your door

 

2-     Use the level to mark a horizontal line over the spot where you would like to install the Viewer, and/or place the installation label on the desired location outside the door making sure you keep it horizontal to the line.

 

3-     Use the 1/8” starter bit to drill a small hole where the center of the opening will be and to drill any necessary holes to accommodate the spikes behind the outside cover of the Viewer.

 

4-     Use the recommended hole saw for the viewer being installed, and start slowly by placing the pilot drill over the center of the previously drilled 1/8” opening.

 

5-     Start drilling from the outside of the door until the pilot drill protrudes lightly through the interior side of the door.

 

6-     Remove the hole saw and go to the inside and finish drilling the hole out, taking care not to chip or splinter the door.

 

7-     Disassemble the outside prism cover casing from the main body of the viewer by turning counterclockwise until it is off.

 

8-     Insert the outer prism cover casing to the exterior side of the door with the spikes into the pre-drilled holes to set it flush with the surface of the door.

 

9-     Insert the viewer main body into the hole form the interior side of the door and turn clockwise while holding the outer cover in place until it is tightly held. Do not over tighten.

 

10- Secure the viewer by turning the fastening ring until it is snug with the door surface.

 

 

© PeepHole Security 2003   www.peepholesecurity.com 

Text Box:                  

                                                                                   

 

 

 

 

 

 

 

 

 


                                                                                                                           

                                                   

Inside Lens     Adjusting       Inner            Outside Prism                                                   

 Cover                Ring              Cylinder       Cover

  

Wide Angle Door Viewers Overall Diameters:

 

Model

 

Inside Lens Cover

 Adjusting Ring

 Inner Cylinder*

Door  Width**

UltraVision

 

63mm ( 2 ½” )

 75mm ( 2 Ύ” )

 56mm ( 2 Ό” )

 Ύ   – 1 Ύ

SuperVision

 

58mm ( 2 Ό” )

 60mm ( 2 3/8” )

 45mm ( 1 Ύ” )

 Ύ  -  1 Ύ

WideVision

 

55mm ( 2 1/8” )

 60mm ( 2 3/8” )

 36mm ( 1 ½” )

 Ύ  -  1 ½

All measurements are approximate

 

 

 

 

Specifications subject to change without notice

© PeepHole Security 2003     www.peepholesecurity.com

 

                                                                                    Inner Lens Cover

                                        Inner Cylinder 

                                                                                             

                        Outside Lens Cover 

Outside Lens

 

Door Viewer / Scopes Overall Diameters

MODEL

 

OUTSIDE LENS COVER

INNER CYLINDER*

INNER LENS COVER

DOOR WIDTH**

NuScope

 

45mm (1 Ύ”)

26mm (1.0”)

33mm (1 Ό”)

1 5/8” – 2.0”

Zscope

 

35mm (1 3/8”)

26mm (1.0”)

35mm (1 3/8”)

1 Ό” – 2.0”

MiniScope

 

26mm (1.0”)

14mm (9/16”)

17mm (11/16”)

5/8” – 1 3/8”

XtraScope

 

26mm ( 1.0”)

14mm (9/16”)

17mm (11/16”)

1 3/8” – 2 1/8”

EZView

 

35mm (1 3/8”)

26mm (1.0”)

35mm (1 3/8”)

1 5/8” – 2 3/8”

EZViewEX

 

45mm (1 3/4”)

26mm (1.0”)

45mm (1 3/4”)

2 3/8” – 3.0”

EZViewEXC

 

45mm (1 3/4”)

26mm (1.0”)

45mm (1 3/4”)

2 3/8” – 3.0”

All measures are approximate

 

Specifications subject to change without notice

© PeepHole Security 2006     www.peepholesecurity.com